Parta de su proceso y encuentre el instrumento adecuado
Aprenda los principios de medición, compruebe las condiciones del proceso, configure productos y guarde recursos técnicos.

La edición en español aún no está disponible. A continuación se muestra la versión completa en inglés.

← Volver a la base de conocimientos
Selección y aplicaciones3 min de lecturaIdioma del contenido: inglésActualizado 23 de octubre de 2026

Electromagnetic flowmeters: Can they measure oils and gases?

Oils and gases are generally nonconductive and do not meet the requirements of conventional electromagnetic flow measurement. Assess other measurement principles for these media.

Direct answer

Oils and gases are generally nonconductive and do not meet the requirements of conventional electromagnetic flow measurement. Assess other measurement principles for these media.

With no stable, continuous conductive phase, conventional electrodes cannot reliably pick up the induced voltage. Changing the units does not address that physical limitation.

What to check and when it applies

Compare actual capabilities under identical operating conditions. Check the most demanding condition separately from long-term operation to determine whether the limitation lies in the measurement, mechanical installation or interface. If candidate data use different media or reference conditions, align the assumptions before comparing. Do not combine maxima from different conditions.

The question for an electromagnetic flowmeter is whether the continuous phase is a conductive liquid. When judging interchangeability, check mechanical, electrical and functional compatibility as well as calibration pairing. Matching housings or connections establish only part of that compatibility. Record the software options and accessories actually supplied. When freezing a configuration, retain the full model, drawings and verification requirements. After maintenance, check which parts of the original configuration the replacement affected.

How to perform this check

  • First check whether the continuous phase is a conductive liquid. Record flow, electrode information and empty-pipe diagnostics. Mark which data you actually obtained. Treat undocumented diagnostics or functions as unconfirmed.
  • Tabulate the minimum, usual and most demanding operating conditions relevant to measuring the oil or gas. Indicate the duration and source of the data for each condition.
  • Compare conditions before and after checking whether the continuous phase is a conductive liquid. Select a reference suited to the equipment and conditions. Keep the original instrument configuration and process conditions during the comparison. Change only one factor at a time, guided by the evidence.

Example: how to draw a conclusion

Consider a customer asking to measure compressed air with an electromagnetic meter. If the medium under consideration is an insulating oil, increasing the current range or selecting mass units will likewise not provide the conductive path that a conventional electromagnetic meter requires.

Start by comparing the current conditions with the conditions used to select the original meter.

Confirm the findings and document the handover

The conclusion should answer whether the oil or gas can be measured. Record the evidence on whether the continuous phase is a conductive liquid, which conditions were covered, the reference used and what remains to be confirmed. Retain the original records and configuration. A single simulation at the output cannot be signed off as a pass for parts of the measurement chain that were not tested.

This is an illustrative example. Use the actual model specifications and site procedures for limits and operating conditions. Reference material does not replace Doweston supply specifications or certifications.

Aplique estos conocimientos a la selección

Clientes y compras

Compruebe las condiciones reales y los criterios de aceptación con el artículo y la documentación del producto. Envíe las cuestiones pendientes al servicio técnico de DOWESTON.

Equipos comerciales y técnicos

Anote las preguntas del cliente y sus condiciones de servicio. Compruebe el rango, las conexiones y las condiciones de uso en la documentación del modelo seleccionado.

Convierta las preguntas en criterios de selección

Reúna los datos del fluido, las conexiones, la instalación y los criterios de aceptación del producto, y revise los puntos pendientes con DOWESTON.

Elegir un producto y preparar las condiciones de servicio
¿Aún no ha iniciado sesión en DOWESTON?
Cree una cuenta para empezar a seleccionar, consultar precios y recibir nuestro boletín con las últimas novedades.
Productos y servicios
Doweston ofrece una gama de servicios para ayudarle a construir rápidamente sistemas de instrumentación automatizada. Contáctenos para más información.
¿Listo para comprar?
Si desea comprar productos,
solo contacte con nuestro equipo de ventas — estaremos encantados de ayudarle.
Quiénes somos
DOWESTON ofrece soluciones de medición precisas y fiables
¡productos de detección y sensores fiables para todos los sectores!
¿Necesita servicio?
Si desea optimizar la producción y reducir los parones,
podemos ayudarle a elegir las piezas de repuesto y los productos de servicio adecuados.
Editar configuración

Nombre del producto

Marca

Modelo

Confirmar cambios Cancelar
Su pantalla puede ser demasiado pequeña para una mejor experiencia.
Le recomendamos continuar en un ordenador,
¡o contacte de inmediato con un ingeniero para su selección!
¿Servicio más rápido? Llame al
400-888-4436
Seguir navegando