Des conditions du procédé au bon instrument
Comprenez les principes de mesure, vérifiez les conditions du procédé, configurez les produits et conservez vos ressources techniques.

La version française n’est pas encore disponible. La version complète en anglais est présentée ci-dessous.

← Retour à la base de connaissances
Sélection et applications3 min de lectureLangue du contenu: anglaisMis à jour 23 octobre 2026

Electromagnetic flowmeter display and current output disagree: how to troubleshoot

The display and current output may use different variables, or the control-system range may be out of sync. Check the meter variable, output mapping, measured loop current and control-system scaling in order.

Separate the display, output and control-system settings

The display and current output may use different variables, or the control-system range may be out of sync. Check the meter variable, output mapping, measured loop current and control-system scaling in order.

The local variable, output mapping and PLC conversion are separate stages.

Find the first stage with a mismatch

A proportional difference often points to an incorrect range or variable. For a fixed offset, also check the zero and units. Measure the current at a stable process condition and compare it with settings at both ends. If the measured loop current is correct but the engineering value is wrong, inspect the scaling in the receiving system.

Record stable low, middle and high points. Put the raw measurement, local engineering value, transmitted signal and system display in the same record. Proportional and fixed offsets help narrow the checks but are not conclusive on their own. An updating communication link does not prove the address is correct. Use a known, permitted change to verify direction and units. Correct the first stage at which the error appears.

Checks on site

  • At a known stable point, record the local value, measured current, and the lower and upper limits configured in the receiving system. Include available flow, electrode and empty-pipe diagnostics, marking which readings were captured and which functions are supported.
  • Draw the terminals by function. Identify active and passive connections, common terminals and the actual input and output types.
  • Compare stable readings at low, middle and high points using a suitable reference. Keep the original settings and operating conditions on record. Address one factor at a time based on the evidence.

Example: the control system uses a different range

Suppose the meter transmits volumetric flow while the control system interprets it using a mass-flow scale. If 0 to 100 is mapped to 4 to 20 milliamps, 12 milliamps corresponds to 50. A PLC configured for 0 to 200 will display 100.

If the local value or transmitted signal is already correct, fix the receiving interface or scale. If the original response is abnormal, trace the issue back to sensing, power and wiring.

Save the loop data and scaling settings

Support your conclusion with the local value, measured current and system value at stable low, middle and high points. Record the conditions covered, the comparison basis and open questions. Keep the original output and PLC scaling records. One test simulating the output cannot verify the measurement stages it bypasses.

This is an illustrative case. Follow the limits of the installed model and the site procedures. Use Doweston’s supply documents to confirm equipment specifications and certification.

Appliquez ces connaissances à la sélection

Clients et achats

Vérifiez les conditions réelles et les critères de réception dans l’article et la documentation du produit. Soumettez les points ouverts au service technique DOWESTON.

Équipes commerciales et techniques

Notez les questions du client et ses conditions de service. Vérifiez la plage, les raccordements et les conditions d’utilisation dans la documentation du modèle sélectionné.

Transformez les questions en critères de sélection

Relevez le fluide, les raccordements, le montage et les critères de réception du produit, puis examinez les points ouverts avec DOWESTON.

Choisir un produit et préparer les conditions de service
Pas encore connecté à DOWESTON ?
Créez un compte pour commencer la sélection, consulter les prix et recevoir notre lettre d'information sur les dernières nouveautés.
Produits et services
Doweston propose une gamme de services pour vous aider à construire rapidement vos systèmes d'instrumentation automatisés. Contactez-nous pour en savoir plus.
Prêt à acheter ?
Si vous souhaitez acheter des produits,
contactez simplement notre équipe commerciale — nous serons ravis de vous aider.
Qui sommes-nous
DOWESTON fournit des solutions de mesure précises et fiables
— des produits de détection et de capteurs fiables dans tous les domaines !
Une demande de service ?
Si vous souhaitez optimiser votre production et réduire les arrêts,
nous pouvons vous aider à choisir les pièces de rechange et les services adaptés.
Modifier la configuration

Nom du produit

Marque

Modèle

Confirmer les modifications Annuler
Votre écran est peut-être trop petit pour une navigation optimale.
Nous vous recommandons de continuer sur un ordinateur,
ou contactez immédiatement un ingénieur pour votre sélection !
Service plus rapide ? Appelez le
400-888-4436
Continuer la navigation