Parta de su proceso y encuentre el instrumento adecuado
Aprenda los principios de medición, compruebe las condiciones del proceso, configure productos y guarde recursos técnicos.

La edición en español aún no está disponible. A continuación se muestra la versión completa en inglés.

← Volver a la base de conocimientos
Selección y aplicaciones3 min de lecturaIdioma del contenido: inglésActualizado 23 de octubre de 2026

Electromagnetic flowmeters: why must the measuring tube stay full?

A conventional full-bore electromagnetic flowmeter calculates flow using the complete cross-sectional area of the tube. A partly filled tube invalidates that assumption and can disrupt measurement.

Check pipe fill before changing the meter settings

A conventional full-bore electromagnetic flowmeter calculates flow using the complete cross-sectional area of the tube. A partly filled tube invalidates that assumption and can disrupt measurement.

Partial fill changes the wetted area and may interrupt electrode contact. Check how to maintain a full tube before changing the configured pipe diameter.

Evaluate the full operating cycle

The tube must remain full throughout the operating cycle, including startup and shutdown. Gas can collect at high points, a free discharge can lower the liquid level, and the pipe can drain after the pump stops. Check the installation elevations and pressure conditions. The absence of an alarm is not proof that the tube is always full and free of gas.

Identify high points and drain paths. When comparing replacement meters, check mechanical and electrical connections, functions and calibration compatibility. Similar appearance or connections are only part of the comparison. Verify software options and accessories against the actual delivery. Record the complete model code, drawings and checks once the configuration is fixed. After service, verify which original installation conditions the replacement changed.

Field checks

  • Identify the highest points and drain paths. Record flow readings and any electrode or empty-pipe diagnostics available from the instrument. Flag readings you collected and diagnostic functions the meter actually supports.
  • List the minimum, typical and most unfavorable fill conditions. Record how long each lasts and where the data came from.
  • Select a reference suited to the instrument and process. Record the original configuration and operating conditions before the comparison. Change one factor at a time based on the observed evidence.

Example: gravity drainage and pump restart

Suppose a gravity drain carries water only in the bottom half of the pipe. If the crown is exposed to air after the pump stops and the tube fills only some time after restart, mark which data are valid before and after the transition.

Compare the current conditions with the conditions used to select the meter.

Document what was verified

Support the conclusion about tube fill with observations of high points and drain paths. Record the operating states covered, the comparison basis and any open items. Retain the observations and original setup. Simulation at the output verifies only the portion of the measurement chain that was tested.

This is an illustrative case. Follow the limits of the installed model and the site procedures. Use Doweston’s supply documents to confirm equipment specifications and certification.

Aplique estos conocimientos a la selección

Clientes y compras

Compruebe las condiciones reales y los criterios de aceptación con el artículo y la documentación del producto. Envíe las cuestiones pendientes al servicio técnico de DOWESTON.

Equipos comerciales y técnicos

Anote las preguntas del cliente y sus condiciones de servicio. Compruebe el rango, las conexiones y las condiciones de uso en la documentación del modelo seleccionado.

Convierta las preguntas en criterios de selección

Reúna los datos del fluido, las conexiones, la instalación y los criterios de aceptación del producto, y revise los puntos pendientes con DOWESTON.

Elegir un producto y preparar las condiciones de servicio
¿Aún no ha iniciado sesión en DOWESTON?
Cree una cuenta para empezar a seleccionar, consultar precios y recibir nuestro boletín con las últimas novedades.
Productos y servicios
Doweston ofrece una gama de servicios para ayudarle a construir rápidamente sistemas de instrumentación automatizada. Contáctenos para más información.
¿Listo para comprar?
Si desea comprar productos,
solo contacte con nuestro equipo de ventas — estaremos encantados de ayudarle.
Quiénes somos
DOWESTON ofrece soluciones de medición precisas y fiables
¡productos de detección y sensores fiables para todos los sectores!
¿Necesita servicio?
Si desea optimizar la producción y reducir los parones,
podemos ayudarle a elegir las piezas de repuesto y los productos de servicio adecuados.
Editar configuración

Nombre del producto

Marca

Modelo

Confirmar cambios Cancelar
Su pantalla puede ser demasiado pequeña para una mejor experiencia.
Le recomendamos continuar en un ordenador,
¡o contacte de inmediato con un ingeniero para su selección!
¿Servicio más rápido? Llame al
400-888-4436
Seguir navegando