Parta de su proceso y encuentre el instrumento adecuado
Aprenda los principios de medición, compruebe las condiciones del proceso, configure productos y guarde recursos técnicos.

La edición en español aún no está disponible. A continuación se muestra la versión completa en inglés.

← Volver a la base de conocimientos
Selección y aplicaciones3 min de lecturaIdioma del contenido: inglésActualizado 23 de octubre de 2026

Electromagnetic flowmeter display and current output disagree: how to troubleshoot

The display and current output may use different variables, or the control-system range may be out of sync. Check the meter variable, output mapping, measured loop current and control-system scaling in order.

Separate the display, output and control-system settings

The display and current output may use different variables, or the control-system range may be out of sync. Check the meter variable, output mapping, measured loop current and control-system scaling in order.

The local variable, output mapping and PLC conversion are separate stages.

Find the first stage with a mismatch

A proportional difference often points to an incorrect range or variable. For a fixed offset, also check the zero and units. Measure the current at a stable process condition and compare it with settings at both ends. If the measured loop current is correct but the engineering value is wrong, inspect the scaling in the receiving system.

Record stable low, middle and high points. Put the raw measurement, local engineering value, transmitted signal and system display in the same record. Proportional and fixed offsets help narrow the checks but are not conclusive on their own. An updating communication link does not prove the address is correct. Use a known, permitted change to verify direction and units. Correct the first stage at which the error appears.

Checks on site

  • At a known stable point, record the local value, measured current, and the lower and upper limits configured in the receiving system. Include available flow, electrode and empty-pipe diagnostics, marking which readings were captured and which functions are supported.
  • Draw the terminals by function. Identify active and passive connections, common terminals and the actual input and output types.
  • Compare stable readings at low, middle and high points using a suitable reference. Keep the original settings and operating conditions on record. Address one factor at a time based on the evidence.

Example: the control system uses a different range

Suppose the meter transmits volumetric flow while the control system interprets it using a mass-flow scale. If 0 to 100 is mapped to 4 to 20 milliamps, 12 milliamps corresponds to 50. A PLC configured for 0 to 200 will display 100.

If the local value or transmitted signal is already correct, fix the receiving interface or scale. If the original response is abnormal, trace the issue back to sensing, power and wiring.

Save the loop data and scaling settings

Support your conclusion with the local value, measured current and system value at stable low, middle and high points. Record the conditions covered, the comparison basis and open questions. Keep the original output and PLC scaling records. One test simulating the output cannot verify the measurement stages it bypasses.

This is an illustrative case. Follow the limits of the installed model and the site procedures. Use Doweston’s supply documents to confirm equipment specifications and certification.

Aplique estos conocimientos a la selección

Clientes y compras

Compruebe las condiciones reales y los criterios de aceptación con el artículo y la documentación del producto. Envíe las cuestiones pendientes al servicio técnico de DOWESTON.

Equipos comerciales y técnicos

Anote las preguntas del cliente y sus condiciones de servicio. Compruebe el rango, las conexiones y las condiciones de uso en la documentación del modelo seleccionado.

Convierta las preguntas en criterios de selección

Reúna los datos del fluido, las conexiones, la instalación y los criterios de aceptación del producto, y revise los puntos pendientes con DOWESTON.

Elegir un producto y preparar las condiciones de servicio
¿Aún no ha iniciado sesión en DOWESTON?
Cree una cuenta para empezar a seleccionar, consultar precios y recibir nuestro boletín con las últimas novedades.
Productos y servicios
Doweston ofrece una gama de servicios para ayudarle a construir rápidamente sistemas de instrumentación automatizada. Contáctenos para más información.
¿Listo para comprar?
Si desea comprar productos,
solo contacte con nuestro equipo de ventas — estaremos encantados de ayudarle.
Quiénes somos
DOWESTON ofrece soluciones de medición precisas y fiables
¡productos de detección y sensores fiables para todos los sectores!
¿Necesita servicio?
Si desea optimizar la producción y reducir los parones,
podemos ayudarle a elegir las piezas de repuesto y los productos de servicio adecuados.
Editar configuración

Nombre del producto

Marca

Modelo

Confirmar cambios Cancelar
Su pantalla puede ser demasiado pequeña para una mejor experiencia.
Le recomendamos continuar en un ordenador,
¡o contacte de inmediato con un ingeniero para su selección!
¿Servicio más rápido? Llame al
400-888-4436
Seguir navegando